BLT Products

Three axis plastic injection robot manipulator BRTNG11WSS3P, F

Three axis servo manipulator BRTNG11WSS3P,F

Short Description

BRTNG11WSS3P/F series apply to all types of horizontal injection machine ranges of 250T-480T for take-out products. The vertical arm is the telescopic type with the product arm.


Main Specification
  • Recommended I.M.M (ton): 250T-480T
  • Vertical Stroke (mm): 1150
  • Traverse Stroke (mm): 1700
  • Max loading (KG): 2
  • Weight (KG): 330
  • Product Detail

    Product Tags

    Product Introduction

    For take-out products, all types of horizontal injection machines in the 250T–480T range can be used with the BRTNG11WSS3P/F series. The vertical arm has a product arm and is telescoping. The three-axis AC servo drive has a shorter forming cycle, precise positioning, and time savings compared to comparable products. The manipulator will enhance production by 10% to 30% after installation, lower product failure rates, guarantee operator safety, need less staff, and precisely manage output to cut down on waste. Fewer signal lines, long-distance communication, good expansion performance, strong anti-interference ability, high repeatability of positioning, capacity to concurrently control multiple axes, easy equipment maintenance, and low failure rate are all advantages of the three-axis driver and controller integrated system.

    Accurate Positioning

    Accurate Positioning

    Fast

    Fast

    Long Service Life

    Long Service Life

    Low Failure Rate

    Low Failure Rate

    Reduce labor

    Reduce Labor

    Telecommunication

    Telecommunication

    Basic Parameters

    Power Source (KVA)

    Recommended IMM (ton)

    Traverse Driven

    Model Of EOAT

    5.38

    250T-480T

    AC Servo motor

    two suctions two fixtures

    Traverse Stroke (mm)

    Crosswise Stroke (mm)

    Vertical Stroke (mm)

    Max Loading (kg)

    1700

    700

    1150

    2

    Dry Take Out Time (sec)

    Dry Cycle Time (sec)

    Air Consumption (NI/cycle)

    Weight (kg)

    0.68

    4.07

    3.2

    330

    Model illustration W: Telescoping platform. S: Product arm S3: AC Servo-driven three-axis (Traverse axis, Vertical axis, and Crosswise axis)

    The cycle time that was described above was determined by an internal test standard at our business. They will change depending on the machine's real operation during the application process.

    Trajectory Chart

    BRTNG11WSS3P infrastructure

    A

    B

    C

    D

    E

    F

    G

    1482

    2514.5

    1150

    298

    1700

    /

    219

    H

    I

    J

    K

    L

    M

    N

    /

    /

    1031

    /

    240

    242

    700

    No further notice if the specification and appearance are changed due to improvement and other reasons. Thank you for your understanding.

    Cylinder Inspection

    1.When use of cylinders, an operating temperature range of 5 to 60 °C is perfect; sealing must be taken into consideration when this range is exceeded; Accidents may happen if the surrounding temperature is below 5 °C because water in the circuit freezes, hence freezing prevention should be taken into account;

    2.Avoid using the cylinder in corrosive environments as it might be damaged or perform poorly;

    3.Clean, low-moisture compressed air must be utilized;

    4.Cutting fluid, coolant, dust, and splashes are not acceptable working conditions for the cylinder; A dust cover must be attached to the cylinder if usage in this environment is required;

    5.If the cylinder is left unused for an extended period of time, it should be operated on a regular basis and maintained with oil to avoid corrosion.

    6. When disassembling and reassembling objects connected to the cylinder shaft end, the cylinder must be pushed into position (the cylinder shaft center cannot be pulled out for disassembly and rotation), evenly locked under equal force, and manually pushed until no interference is confirmed before starting gas supply.

    Application Industry

    This product is suitable for 250T-480T horizontal injection molding machine's finished products and water outlet to take out; It is especially suitable for small injection moulding objects such as cosmetics, drink bottles, food, sanitary ware, medical appliances and other products of various packaging objects.

    Recommended Industries

    mold injection application
    • Injection Molding

      Injection Molding


  • Previous:
  • Next: